Deye

Deye hibakódok

• F30 Hibaelhárítás Deye invertereken
• F040 CURRENT_MODULE_FAULT
• 30 Internal comm fails
• F028 BMS_ADDR_REPEAT
• F024 ULTIMATE_PROTECTION
• F052 PACK_THERMAL_RUNAWAY
• F015 DSG_OVER_CUR_LEV_2
• F20 DC over current (HW)
• 26 Cell voltage sampling fails
• F58 Battery BMS comm lost
• 02 Cell under voltage
• W3 Grid Phase Wrong
• 28 Mosfet short circuit
• F032 PCS_RS485_COMM_ERROR
• F048 BMU_COMM_ERROR
• 51 Charge inverses
• F53 DC_VoltLow_Fault (BUS low)
• F039 CURRENT_SAMPLE_ERROR
• F023 HEAT_RELAY_ADHESION
• 55 TEMP_OPEN_WIRE_FAIL
• F48 AC under frequency
• 01 Cell over voltage
• F047 CHG_VOLT_LOW
• F057 PACK_AFE_COMM_ERROR
• F055 W5500_SPI_COMM_FAIL
• F026 FUSE_BLOWN
• 45 Cur Limit Mos Adhesion
• F34 AC overload
• F47 AC over frequency
• F007 OVER_DIFF_VOLT_LEV_2
• 11 Cell voltage over difference
• F42 Parallel_Version_Fault
• F056 LC_COMM_LOST
• F060 SINGLE_CLUSTER_POWER_DOWN
• 31 PCS comm fails
• F059 CELL_TYPE_MISMATCH_ERROR
• F009 CELL_OVER_VOLT_LEV_2
• 06 Discharge over current
• F018 HEAT_OVER_TEMP_LEV_2
• W2 FAN WARN — fan abnormal alarm
• W32 Parallel-comm-warn — unstable parallel communication
• F011 PRE_CHG_RES_OVER_TEMP_LEV_2
• 25 AFE comm fails
• F046 PRECHAGE_ERROR
• F013 SOUTH_CONNECTOR_OVER_TEMP_LEV_2
• 04 Ultimate_Protection
• F034 BAT_VOLT_SAMP_ERROR
• F29 Parallel CAN-bus / comm fault
• F002 SUM_LOW_VOLT_LEV_2
• F22 Emergency stop (remote shutdown)
• F006 DSG_LOW_TEMP_LEV_2
• F52 DC_VoltHigh_Fault (BUS high)
• F57 BAT1 OR 2_VoltLow_Fault
• F029 INTERNAL_COMM_ERROR
• F014 CHG_OVER_CUR_LEV_2
• F004 DSG_OVER_TEMP_LEV_2
• F21 Tz_HV_Overcurr / BUS overcurrent
• F033 FUSE_VOLT_SAMP_ERROR
• 46 Mos Adhesion Susp
• F26 DC busbar unbalanced
• 07 Cell over temperature
• 19 AFE-OCDL/OCD1/OCD2
• F025 POWER_SUPPLY_FAULT
• W31 Battery_comm_warn — abnormal battery communication
• 12 Cell temperature over difference
• 53 Fuse blown
• F050 MBMS_NTC_BREAKLINE_ERROR
• 48 Heat error
• F044 HEAT_RELAY_DRIVE_FAULT
• F24 DC insulation impedance fault
• F051 BMU_NTC_BREAKLINE_ERROR
• F23 Tz_GFCI_OC transient
• F042 CHG_RELAY_DRIVE_FAULT
• 29 EEPROM error
• F019 SOC_LOW_LEV_2
• 13 Mos over temperature
• 08 Cell under temperature
• F030 PCS_CAN_COMM_FAIL
• F031 PCS_ERROR_STATE
• F008 OVER_DIFF_TEMP_LEV_2
• F053 PACK_FIRE_FAULT
• F020 DSG_RELAY_ADHESION
• F16 GFCI / AC leakage current
• F035 MOT_VOLT_SAMP_ERROR
• F058 BLE_INIT_FAULT
• F022 CHG_RELAY_ADHESION
• F012 NORTH_CONNECTOR_OVER_TEMP_LEV_2
• F010 CELL_LOW_VOLT_LEV_2
• 47 Heat Mos adhesion
• 14 Heating film over temperature
• F18 AC over current (HW)
• F016 SOC_OVER_LEV_2
• 49 Over connect temp
• F041 POS_RELAY_DRIVE_FAULT
• 54 VOLT_OPEN_WIRE_FAIL
• F037 CELL_VOLT_SAMPLE_ERROR
• F017 INSULATION_FAILURE_TWO
• F01 DC reversed / input polarity
• 27 Temp sampling fails
• F005 CHG_LOW_TEMP_LEV_2
• F043 DSG_RELAY_DRIVE_FAULT
• F42 AC line low voltage
• F41 Parallel system stop
• F038 TEMP_SAMPLE_ERROR
• F036 HTP_VOLT_SAMP_ERROR
• 05 Charge over current
• F07 DC_START_Failure (BUS won't build)
• W4 Meter Comm Fail — meter communication failure
• F054 TCP_CONNECT_FAIL
• 24 AFE-SCDL/SCD
• F001 SUM_OVER_VOLT_LEV_2
• F021 POS_RELAY_ADHESION
• F15 AC over current (SW)
• 32 Master address repeat
• 52 Over terminal temp
• F46 Backup battery fault
• F35 No AC grid
• F64 Heatsink high temperature
• 50 Pre charge fail
• F003 CHG_OVER_TEMP_LEV_2
• F045 EEPROM_ERROR
• F54 BAT1 OR 2_VoltHigh_Fault
• F049 BMU_NUMBER_ERROR
• F027 BMU_ADDR_REPEAT
• F13 - Grid mode changed
• W03 hibakód (Grid phase wrong) helyreállítása Deye inverteren