---
title: SolaX CT/Meter connector (en)
description: SolaX systems can be equipped with a battery or an EV charger, but even if you only want to utilize phase imbalance, measurement setup is still required. This can be done either using current transformers (CT clamps) or a smart meter — both of which use the same port on SolaX inverters.
---

[Skip to content](https://support.solar-kit.eu/en/knowledge-base/solax-viszwatt-védelem-beállítások-0-0-0-0-0-0-2#main-content)

- [English](https://support.solar-kit.eu/en/knowledge-base/solax-viszwatt-v%C3%A9delem-be%C3%A1ll%C3%ADt%C3%A1sok-0-0-0-0-0-0-2)
- [Magyar](https://support.solar-kit.eu/hu/tudastar/solax-ct-meter-csatlakozó)

English

Show submenu for translations

[![solarkit-logo](https://support.solar-kit.eu/hs-fs/hubfs/solarkit-logo-color.jpg?width=200&height=55&name=solarkit-logo-color.jpg)](https://support.solar-kit.eu/en/knowledge-base?hsLang=en)

Open main navigation

Close main navigation

- - [English](https://support.solar-kit.eu/en/knowledge-base/solax-viszwatt-v%C3%A9delem-be%C3%A1ll%C3%ADt%C3%A1sok-0-0-0-0-0-0-2)
    - [Magyar](https://support.solar-kit.eu/hu/tudastar/solax-ct-meter-csatlakozó)

  English
  
  Show submenu for translations
- [Go to the webshop](https://shop.solar-kit.eu/)

[Go to the webshop](https://shop.solar-kit.eu/)

 How can we help?

- There are no suggestions because the search field is empty.

1. [SOLARKIT Knowledge Base](https://support.solar-kit.eu/en/knowledge-base?hsLang=en)
2. [SolaX](https://support.solar-kit.eu/en/knowledge-base/solax?hsLang=en)

# SolaX CT/Meter connector (en)

## SolaX systems can be equipped with a battery or an EV charger, and even if we simply want to take advantage of phase asymmetry, measurement still needs to be implemented. This can be done with CT clamps or a smart meter, but in the case of SolaX these will use the same port. In this article we show how this is possible, where to find this port, and what to pay attention to.

Because of the situations mentioned above, setting up measurement is almost always necessary for these inverters. Therefore, the manufacturer includes **current transformer clamps** in the package. Each of the **three phases** uses **two wires** for measurement, meaning the CT-based measurement requires **six conductors** in total.

From the bottom view of the inverter, the connector highlighted in **red** is the one referred to in this article.  
![](https://support.solar-kit.eu/hs-fs/hubfs/undefined-Nov-04-2025-08-24-57-6355-AM.png?width=1222&height=454&name=undefined-Nov-04-2025-08-24-57-6355-AM.png)

SolaX supplies **three CT clamps** already connected to a **plug head**, from which you must extend a **communication cable** with **RJ45 connectors** at both ends. One end connects to the inverter’s **CT/Meter port**, and the other to the **RJ45 ends of the CT clamps**. Since this creates a **male-to-male connection**, the manufacturer provides a **female-to-female adapter** with the communication cable.

In the **User Manual**, there is a table showing the **pin layout** of this port:  
![](https://support.solar-kit.eu/hs-fs/hubfs/undefined-Nov-04-2025-08-24-57-3575-AM.png?width=1053&height=521&name=undefined-Nov-04-2025-08-24-57-3575-AM.png)

- Pins **4–5** are reserved for the **smart meter**.
- Pins **1–3** and **6–8** correspond to the **CT clamps**.

Thus, if you only intend to use a **meter**, you only need to connect **two pins** in the communication cable. For **CT clamps**, **six pins** are required. However, by connecting both CT clamps and the meter, you can create **two separate measurement points**. 

- [Deye](https://support.solar-kit.eu/en/knowledge-base/deye?hsLang=en#main-content)

    - [Deye error codes](https://support.solar-kit.eu/en/knowledge-base/deye?hsLang=en#deye-error-codes)
- [Dyness](https://support.solar-kit.eu/en/knowledge-base/dyness?hsLang=en#main-content)

    - [Dyness error codes](https://support.solar-kit.eu/en/knowledge-base/dyness?hsLang=en#dyness-error-codes)
- [FoxESS](https://support.solar-kit.eu/en/knowledge-base/foxess?hsLang=en#main-content)

    - [FoxESS error codes](https://support.solar-kit.eu/en/knowledge-base/foxess?hsLang=en#foxess-error-codes)
- [Huawei](https://support.solar-kit.eu/en/knowledge-base/huawei?hsLang=en)
- [SolaX](https://support.solar-kit.eu/en/knowledge-base/solax?hsLang=en#main-content)

    - [SolaX error codes](https://support.solar-kit.eu/en/knowledge-base/solax?hsLang=en#solax-error-codes)
- [General](https://support.solar-kit.eu/en/knowledge-base/general?hsLang=en)
- [Webshop User Guide](https://support.solar-kit.eu/en/knowledge-base/webshop-user-guide?hsLang=en)

[![Chill listening crop-3](https://support.solar-kit.eu/hs-fs/hubfs/solarkit-logo-color-1.jpg?width=87&height=24&name=solarkit-logo-color-1.jpg "Chill listening crop-3")](http://solar-kit.eu)

**Knowledge Base** - [shop.solar-kit.eu](http://shop.solar-kit.eu)

<https://www.facebook.com/SolarKitEurope.eu/> <https://www.instagram.com/solarkit_europe/> <https://www.linkedin.com/company/solarkit> <https://www.youtube.com/@SolarKitEurope>

Copyright © 2026, SOLARKIT Europe Ltd.